EN European Norm Tests Part 23

EN Standards are European Standards. These standards specify requirements for a particular item, material, component, system or service, or describe in detail a particular method or procedure, and tests are performed accordingly.

• EN 1225: 1996; Plastic piping systems. Glass reinforced thermoset plastic (GRP) pipes. Determination of the creep factor under wet conditions and calculation of long-term specific ring stiffness.
• EN 1226: 1996; Plastic piping systems. Glass reinforced thermoset plastic (GRP) pipes. Test method to prove resistance to initial ring deflection.
• EN 1227: 1998; Plastic piping systems. Glass reinforced thermoset plastic (GRP) pipes. Determination of the long-term final relative ring deviation under wet conditions.
• EN 1228: 1997; Plastic piping systems. Glass reinforced thermoset plastic (GRP) pipes. Determination of initial specific ring stiffness.
• EN 1229: 1997; Plastic piping systems. Glass reinforced thermoset plastic (GRP) pipes and fittings. Test methods to prove the tightness of the wall under short-term internal pressure.
• EN 1230-1: 2009; Paper and cardboard intended for contact with foodstuffs. Sensory analysis. Smell
• EN 1230-2: 2009; Paper and cardboard intended for contact with foodstuffs. Sensory analysis. bad taste (defect)
• EN 1231: 1997; Workplace environments. Short-term detector tube measurement systems. Requirements and test methods.
• EN 1232: 1997; Workplace environments. Pumps for personal sampling of chemicals. Requirements and test methods.
• EN 1233: 1997; water quality. Chromium determination. Atomic absorption spectrometric methods.
• EN 1236: 1995; Fertilizers. Determination of bulk density (loose).
• EN 1237: 1995; Fertilizers. Determination of bulk density (guideline).
• EN 1238: 1999; Adhesives. Determination of softening point of thermoplastic adhesives (ring and ball).
• EN 1238: 2011; Adhesives. Determination of softening point of thermoplastic adhesives (ring and ball).
• EN 1240: 1998; Adhesives. Determination of hydroxyl value and/or hydroxyl content.
• EN 1240: 2011; Adhesives. Determination of hydroxyl value and/or hydroxyl content.
• EN 1242: 1998; Adhesives. Determination of isocyanate content.
• EN 1242: 2005; Adhesives. Determination of isocyanate content.
• EN 1242: 2013; Adhesives. Determination of isocyanate content.
• EN 1243: 1999; Adhesives. Determination of free formaldehyde in amino and amidoformaldehyde condensates.
• EN 1243: 2011; Adhesives. Determination of free formaldehyde in amino and amidoformaldehyde condensates.
• EN 1244: 1998; Adhesives. Determination of color and/or color changes of adhesive coatings under the influence of light.
• EN 1245: 1999; Adhesives. pH determination. Test method.
• EN 1246: 1998; Adhesives. Determination of ash and sulfated ash.
• EN 1251-1 : 2000 ; Cryogenic vessels. Portable vacuum insulated containers with a volume not exceeding 1000 liters. basic requirements
• EN 1251-2: 2000; Cryogenic vessels. Portable vacuum insulated containers with a volume not exceeding 1000 liters. Design, manufacture, inspection and testing
• EN 1251-3: 2000; Cryogenic vessels. Portable vacuum insulated containers with a volume not exceeding 1000 liters. operational requirements
• EN 1252-1: 1998; Cryogenic vessels. Materials. Toughness requirements for temperatures below -80^DC
• EN 1253-1: 2015; Gutters for buildings. Compressed floor gutters with a watertight seal of at least 50mm deep
• EN 1253-2: 2015; Gutters for buildings. Trap-free roof drains and floor gutters
• EN 1253-3: 2016; Gutters for buildings. Evaluation of eligibility
• EN 1254-1: 1998; Copper and copper alloys. Plumbing fixtures. Tip fittings for capillary brazing or capillary brazing on copper pipes
• EN 1254-2: 1998; Copper and copper alloys. Plumbing fixtures. Compression end fittings for use with copper pipes
• EN 1254-3: 1998; Copper and copper alloys. Plumbing fixtures. Compression end fittings for use with plastic pipes
• EN 1254-4: 1998; Copper and copper alloys. Plumbing fixtures. Fittings connecting other end connections with capillary or compression ends
• EN 1254-5: 1998; Copper and copper alloys. Plumbing fixtures. Short tip fittings for capillary soldering to copper pipes
• EN 1254-6: 2012; Copper and copper alloys. Plumbing fixtures. Fittings with snap ends
• EN 1254-8: 2012; Copper and copper alloys. Plumbing fixtures. Press-end fittings for use with plastic and multilayer pipes
• EN 1256: 1996; Gas welding equipment. Specification for hose assemblies for equipment for welding, cutting and similar operations.
• EN 1256: 2006; Gas welding equipment. Specification for hose assemblies for equipment for welding, cutting and similar operations.
• EN 1262: 1996; Surfactants. Determination of the pH value of surfactant solutions or dispersions.
• EN 1263-1: 1997; safety nets. Security requirements, test methods
• EN 1263-1: 2014; Temporary work equipment. safety nets. Security requirements, test methods
• EN 1263-2: 1998; safety nets. Security requirements for the establishment of safety nets
• EN 1263-2: 2014; Temporary work equipment. safety nets. Security requirements for positioning boundaries
• EN 1264-1: 1998; Underfloor heating. Systems and components. Definitions and symbols
• EN 1264-1: 2011; Water-based surface embedded heating and cooling systems. Definitions and symbols
• EN 1264-2: 1998; Underfloor heating. Systems and components. Determination of thermal output
• EN 1264-2 : 2008+A1 : 2012 ; Water-based surface embedded heating and cooling systems. Underfloor heating : Prove methods for determining thermal output using calculation and test methods
• EN 1264-3: 1998; Underfloor heating. Systems and components. sizing
• EN 1264-3: 2009; Water-based surface embedded heating and cooling systems. sizing
• EN 1264-4: 2009; Water-based surface embedded heating and cooling systems. Setup
• EN 1264-5: 2008; Water-based surface embedded heating and cooling systems. Heating and cooling surfaces embedded in floors, ceilings and walls. Determination of thermal output
• EN 1265 : 1999+A1 : 2008 ; Machinery safety. Noise test code for foundry machinery and equipment.
• EN 1267: 1999; valves. Flow resistance test using water as test fluid.
• EN 1267: 2012; Industrial valves. Flow resistance test using water as test fluid.
• EN 1269 : 2015 ; Textile floor coverings. Evaluation of impregnations in needle floor coverings by soiling test.
• EN 1270: 1998; playground equipment. Basketball equipment. Functional and safety requirements, test methods.
• EN 1270: 2005; playground equipment. Basketball equipment. Functional and safety requirements, test methods.
• EN 1271: 1998; playground equipment. Volleyball equipment. Functional and safety requirements, test methods.
• EN 1271: 2014; playground equipment. Volleyball equipment. Functional and safety requirements, test methods.
• EN 1272: 1998; Childcare articles. Table top chairs. Security requirements and test methods.
• EN 1273: 2001; Childcare articles. Baby walking frames. Security requirements and test methods.
• EN 1273: 2005; Child use and care articles. Baby walking frames. Security requirements and test methods.
• EN 1274: 1997; Thermal spray. Powders. Composition. Technical terms of supply.
• EN 1274: 2004; Thermal spray. Powders. Composition, technical terms of supply.
• EN 1275: 1997; Chemical disinfectants and antiseptics. Basic fungicidal activity. Test method and requirements (stage 1).
• EN 1275 : 2005 ; Chemical disinfectants and antiseptics. Quantitative suspension testing for evaluation of basic fungicidal or basic yeasticidal activity of chemical disinfectants and antiseptics. Test method and requirements (stage 1).
• EN 1276: 1997; Chemical disinfectants and antiseptics. Quantitative suspension testing for the evaluation of bactericidal efficacy of chemical disinfectants and antiseptics used in food, industrial, domestic and institutional areas. Test method and requirements (stage 2, step 1).
• EN 1276: 2009; Chemical disinfectants and antiseptics. Quantitative suspension testing for the evaluation of bactericidal efficacy of chemical disinfectants and antiseptics used in food, industrial, domestic and institutional areas. Test method and requirements (stage 2, step 1).
• EN 1277: 1996; Plastic piping systems. Thermoplastic piping systems for buried pressureless applications. Test methods for the tightness of elastomeric sealing ring type connections.
• EN 1278 : 1999 ; Chemicals used to treat water intended for human consumption. Ozone.
• EN 1278 : 2010 ; Chemicals used to treat water intended for human consumption. Ozone.
• EN 1279-5 : 2005+A2 : 2010 ; Glass in the building. Insulating glass units. Evaluation of eligibility
• EN 1280-1: 1997; Agent-specific filling systems for anesthetic vaporizers. Rectangular key filling systems
• EN 1281-1: 1997; Anesthetics and respirators. Conical connectors. Cones and sockets
• EN 1281-2: 1996; Anesthetics and respirators. Conical connectors. Threaded, weight-bearing connectors
• EN 1282-1: 1997; Anesthetics and respirators. Tracheostomy tubes. Tubes for adult use
• EN 1282-2 : 2005+A1 : 2009 ; Tracheostomy tubes. pediatric tubes
• EN 1283: 1996; Hemodialyzers, hemodiafilters, hemofilters, hemoconcentrators and their extracorporeal circuits.
• EN 1286: 1999; Sanitary faucet. Low pressure mechanical mixing valves. General technical specification.
• EN 1287: 1999; Sanitary faucet. Low pressure thermostatic mixing valves. General technical specifications.
• EN 1288-1: 2000; Glass in the building. Determination of the bending strength of glass. Glass testing basics
• EN 1288-2: 2000; Glass in the building. Determination of the bending strength of glass. Coaxial double ring testing on flat specimens with large test surface areas
• EN 1288-3: 2000; Glass in the building. Determination of the bending strength of glass. Test with specimen supported at two points (four point bending)
• EN 1288-4: 2000; Glass in the building. Determination of the bending strength of glass. Testing channel shaped glass
• EN 1288-5: 2000; Glass in the building. Determination of the bending strength of glass. Coaxial double ring testing on flat specimens with small test surface areas
• EN 1289: 1998; Non-destructive testing of welds. Penetrant testing of welds. Acceptance levels.
• EN 1290: 1998; Non-destructive testing of welds. Magnetic particle inspection of welds.
• EN 1291: 1998; Non-destructive testing of welds. Magnetic particle testing of welds. Acceptance levels.
• EN 1293: 1999; General requirements for components used in pneumatic pressure relief pipes, drains and sewers.
• EN 1294: 2000; Door leaves. Determination of behavior under moisture changes in successive uniform climates.
• EN 1295-1: 1997; Structural design of buried pipelines under various loading conditions. General Requirements
• EN 1296: 2001; Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roofing. Artificial aging method by prolonged exposure to high temperature.
• EN 1297: 2004; Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roof waterproofing. A method of artificial aging through prolonged exposure to a combination of UV radiation, high temperature and water.
• EN 1298: 1996; Mobile access and work towers. Rules and guidelines for the preparation of an instruction manual.
• EN 1299 : 1997+A1 : 2008 ; Mechanical vibration and shock. Vibration Isolation of Machines. Information for the application of source isolation.
• EN 1300 : 2013 ; Secure storage units. Classification of high security locks according to their resistance to unauthorized opening.
• EN 1301-1: 1997; Aluminum and aluminum alloys. Drawn wire. Technical conditions for inspection and delivery
• EN 1301-1: 2008; Aluminum and aluminum alloys. Drawn wire. Technical conditions for inspection and delivery

Standards facilitate international trade by ensuring compatibility and interoperability of components, products and services. European Standards (ENs) are documents approved by three European Standardization Organizations (ESO), CEN, CENELEC or ETSI; Recognized as competent in the field of voluntary technical standardization for EU Regulation 1025/2012.