Renault 32-00-008-P Interior Trim Parts - General Requirements

The specifications in the standard “Renault 32-00-008-P Interior trim parts - General requirements” developed by the French automobile company Renault define the required characteristics for interior trim parts (cockpit and luggage). Due to their function, some parts must comply with additional requirements specified in the drawing (special tests) or which may be the subject of specific product specifications. For example, the following specifications:

• 32-01-188 Additional ground functional definition
• 32-03-202 Luggage cover
• 32-04-080 Plastic hooks
• 32-07-000 Cardboard hardness
• 32-07-001 Plastic or rubber floor mats
• 32-07-003 Ceiling interior linings
• 32-07-004 Door panel upholstery
• 32-07-007 Luggage vertical floor
• 32-07-018 Barrier networks
• 32-07-019 Hides the anchors of the hubcap separation net
• 32-07-021 Storage covers
• 32-07-024 Ceiling stacking
• 32-07-033 LCV flat panels
• 32-07-034 Cutting the front step
• 32-07-522 Interior door handles
• 32-07-526 Rear package shelves
• 32-07-528 Spare wheel covers and trunk carpet
• 32-07-532 Manual or electrically controlled sunshades
• 32-07-533 Rear sill strip for light commercial vehicles
• 32-07-534 Storage area for motor vehicles
• 32-07-535 Console under the ceiling
• RNDS-C-00126 (32-07-529) Sunshade - Fittings and accessories
• RNDS-C-00373 (32-07-002) Pile floor carpet - Installation and accessories
• RNDS-C-00374 (32-07-523) Interior vehicle isolators
• RNDS-C-00375 (39-07-000) Acoustic absorbers for underbody and engine compartment
• RNDS-C-20276 (32-07-521) Floor pieces and assimilated pieces

Responsibility of the supplier:

• The products must comply with the requirements of the processes initiated by the Renault purchasing department (Renault Group quality policy).
• The supplier must provide a predictive analysis file on reliability (fault trees, predictive calculations based on databases, etc.).
• The provisions of the standard “00-10-415 Production and supply of products - General requirements” shall fully apply to the applicable technical specifications unless expressly stated otherwise.

Onay:

• The supplier must inform Groupe Renault of the means provided to ensure and monitor the quality of components, particularly for non-supplier components.
• The verification procedure is defined by the Renault Group approval. Based on the verification plan, the supplier must list the tests performed in the verification procedure, the performer, the verifier and the deadline for each test. If there are several installations with similar applications for a product type and a variant type, the reliability test can only be performed in the most stringent application.
• The selectivity of verification plans testing does not exempt the supplier from meeting all specifications.
• The responsibility for verification in a project between Renault Group and a supplier is determined during the preparation of the verification plan. The tester must be approved and self-guaranteed by Renault Group in accordance with “Rule 64150-02-0214 for the assessment of the competence of a supplier in measurement, testing and calculations”.
• One step in the verification process is the signature. The supplier must complete the test report, detailed with the measured values ​​for all tests and including all the elements necessary for the evaluation of the result, and send them to Renault Group.
• Parts must be marked according to the standard “00-10-501 Renault marking or Renault / Nissan parts” and the standard “00-10-415 Production and supply of products - General requirements”.
• The traceability of delivered parts must comply with the “01-33-300 Traceability” standard.

Packaging:

• Unless specific provisions are made by the Renault Group, the requirements of standard 00-10-415 must be applied.
• In addition, during the pre-validation phase, the supplier must provide the Renault Group with the packaging in which it plans to use them.
• In any case, parts should not be kept in an area where the temperature exceeds 70 degrees.
• The standard “32-01-154 Temporary protection method for door panels and pillar coverings” must be complied with in accordance with the project request for door panel parts and lower pillar covering.
• These packagings are validated after a transport test between the supplier's site and the Renault site. They must comply with the models chosen and accepted by the supplier and Renault, including international ones.
• The packaging must allow the parts to be stored and transported in a perfectly clean environment, protect the parts from possible damage and not cause any deformation. The description of these parts must also include the conditions of use.

Products defined by existing standards are subject to official regulations in accordance with the requirements defined at the time of approval, the requirements always taking precedence over the requirements present in this standard.

Our organization, which has been trying to support businesses from every sector with its wide range of testing, measurement, analysis and evaluation studies for years, has a strong staff that closely follows the developments in the world in the field of science and technology and constantly improves itself. In this context, testing services in accordance with the "Renault 32-00-008-P Interior trim parts - General requirements" standard are also provided to businesses.